Mould is often found in cupboards

Mould is often found in cupboards, and behind furniture which is pushed close up against a cold wall, this is because there is poor ventilation in cupboards and behind furniture so that any condensation there gets little chance to dry off.Problems do occur because of problems with a building, however many people just do not make sure the property is properly ventilated.Paints with mould inhibitors: -

Longer term protection against the re-appearance of mould can be gained by redecorating the area affected with a mould inhibiting paint. The other ways include; cavity wall insulation, double glazing, internal dry lining of walls and external insulated rendering. In poorly heated rooms they have little effect. The amount of water is often rather more than the original amount of paraffin, because of existing moisture in the air. They cost about ?1 – ?2 per week to run. Some models are ineffective. These washes kill the mould and it’s spores and does provide some short term protection against the re-appearance of mould. The warmer a house the less condensation will occur – providing that the level of humidity is controlled too.When cooking, keep kitchen door shut and window open. In particular if you have mould behind furniture or in cupboards then move them away from the cold outside walls if possible and put ventilation holes in the top and bottom of cupboards if necessaryCleaning: -

Cleaning away mould is best done using an anti-mould solution or wash and there are a number of different brands now on the market. It must be remembered, however, that if there is not heating at all in the house then improving the ventilation won’t make it any warmer.The following notes provide more information about condensation Next to shrinkage, condensation is the most common problem in houses.There are other, more expensive, ways of improving the insulation of a house but loft insulation is the one to start with.INCREASING WARMTH: HEATING AND VENTILATIONA house can be made warmer inside by increasing the level of heating or by increasing the insulation. If condensation is very bad in the house you should consider drying your clothes at a launderette if you can’t dry them outside the house. However there are ways of controlling condensation. In the latter case condensation is often not noticed unless or until mould appears.

The moisture can come from cooking, bathing, washing and drying clothes as well as from paraffin heaters and flue-less gas heaters – even breathing produces condensation. Quite often they have not opened windows or turned extractors on whilst washing or cooking, they live in a property without a chimney, that has double glazing and now fresh air is getting in. These machines remove water from the air and produce heat too.If you use a paraffin heater or flue-less gas heater, be sure the window is open a little.

A relatively cheap way of providing a little extra insulation to a wall is to put expanded polystyrene behind the wallpaper Injection mould (you can buy this in rolls).Loft insulation is the most cost-effective way of improving the insulation of a house and a grant may be available from the council towards providing it in certain circumstances and if you are on supplementary benefit, family credit or housing benefit and if the house has less than 3mm of loft insulation. One way is to reduce the amount of moisture in the air (the “humidity”), or another is to increase the warmth of the surface of the walls or other areas affected..Several companies produce machines called “dehumidifiers”. Reducing condensation is the best way of controlling mould but it is possible to use fungicidal washes and paints also. The machine has to have a large capacity (an extraction rate of 2-4 litres per day is needed).)In cold weather, keep some heating on all the time, i. They dry their clothes over a heater in the living room or bedroom and before long there is water running down the glass on the windows, black mould occurring on walls, corners of ceiling and in built in cupboards. The water in the air then either settles as water droplets on the surface (as it does on windows for example), or, if the surface is absorbent, it soaks into the surface. A little while after using them the surface should be scrubbed clean with a stiff brush.Mould tends to appear on surfaces where condensation takes place regularly. They work best in well heated rooms where the humidity is high. Remember that every gallon of paraffin burnt produces 10 pints of water*(* One gallon of paraffin when burned produces water vapour which turns into water as soon as it touches cold walls and windows. Tumble driers produce a great deal of moist air and this should, ideally, be ducted directly to Cap mould the outside of the house.WAYS TO CONTROL CONDENSATIONSee that your rooms are always warm and properly ventilated.e.When bathing, washing or drying clothes, keep the room door shut and the window open. A number of firms produce these. Too much ventilation in rooms can carry away too much heat and this can cause wall surfaces to get so cold it will actually encourage condensation rather than reduce it.SPECIAL MEASURES AGAINST MOULDGeneral: – The most important action to take against mould is to try and reduce the condensation in the ways described earlier.One the major complaints from a tenant is to contact the Landlord or agent and say they have a damp problem. Condensation occurs when warm moist air meets a cold surface. for 24 hours a day. Because the external walls of a room are usually the coldest they tend to be most affected by condensation (and as a result of mould) particularly at the corners of the room. In short these machines may be very helpful in some cases, but are not a sure fire cure for condensation